About damn, time you signed up!
Hope to see you in your p.o.s
at our next meet Sunday, Oct. 1st....
| South Florida Mitsubishi Enthusiasts https://www.soflamitsu.com/ |
|
| noob https://www.soflamitsu.com/viewtopic.php?f=24&t=35 |
Page 1 of 1 |
| Author: | Spoolin [ Sun Sep 24, 2006 5:20 pm ] |
| Post subject: | noob |
I drive a p.o.s. Mirage and finally joined the site. I know a few DSMer's around allready and Im sure I will meet more of you. See you around Bryan |
|
| Author: | DSMmaniac_Big_O [ Sun Sep 24, 2006 5:33 pm ] |
| Post subject: | |
About damn, time you signed up! Hope to see you in your p.o.s at our next meet Sunday, Oct. 1st....
|
|
| Author: | Xplicit93AWD [ Sun Sep 24, 2006 5:54 pm ] |
| Post subject: | |
Waddap homie, welcome to the board of brotherly love...lol....Hope to see you soon. Aramis |
|
| Author: | Sbeing1 [ Sun Sep 24, 2006 7:28 pm ] |
| Post subject: | |
Velcome. |
|
| Author: | MikeIsBoosted [ Sun Sep 24, 2006 8:21 pm ] |
| Post subject: | |
Sup? Welcome to the club man. |
|
| Author: | Ced [ Sun Sep 24, 2006 10:02 pm ] |
| Post subject: | |
i love colts welcome |
|
| Author: | AllWheelDSM [ Sun Sep 24, 2006 10:19 pm ] |
| Post subject: | |
POS Mirage? Ha ha ha, ha ha, ha ha ha. Ha. That Mirage is far from a piece of shit. Welcome to the boards. |
|
| Author: | sillycon [ Tue Sep 26, 2006 10:14 am ] |
| Post subject: | |
How'd your shit pile run at Norwalk? For some reason it sticks in my head that you were picking up parts "on the way" and put it all back together at the track, yea? |
|
| Author: | Spoolin [ Tue Sep 26, 2006 7:14 pm ] |
| Post subject: | |
I picked up the tranny the day we left for ohio. When I got to norwalk I threw the tranny in and tbelt on because the head had been off. Then the car wouldnt start. No compression. I eventually got it running but the compression is low on 3-4. I never got the shifter cables properly adjusted so I didnt make any decent passes. POS Mirage |
|
| Author: | DSMmaniac_Big_O [ Tue Sep 26, 2006 10:02 pm ] |
| Post subject: | |
Well, I know we don't personally know one another very well. But when you're in South Florida, we're all here for one another. Just post up whenever you need a hand... I also up'ed your board privileges, so enjoy! |
|
| Author: | sillycon [ Wed Sep 27, 2006 9:09 am ] |
| Post subject: | |
Do you think it's bent valves, bad ring seal, or leaking HG? Good luck with the shifter cables -- they can be a pain. I just redid them on my car as the old ones had cracked boots and were starting to "stick". |
|
| Author: | Spoolin [ Wed Sep 27, 2006 2:08 pm ] |
| Post subject: | |
The shifter cables are brand new, just need to spend time adjusting them. The compression is low due to the rings. They werent sealing at all before I got the car running in ohio, 70psi across the board. Now the compression is up on all the cylinders but still not good enough. You can see the blow-bye out the oil fill cap in the valvecover and when I let off after making a pull. I think it was below service limit on 3-4, like 119-130psi. I dont know what the hell happened to the rings as the motor was fine before I had the block oringed. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|